Announcements

Job offersmore »

Tweeting Growers

Last commentsmore »

Top 5 - yesterday

  • No news has been published yesterday.

Top 5 - last week

Top 5 - last month

Exchange ratesmore »




Plant waste could be used to build planes and cars

Using plants and trees to make products such as paper or ethanol leaves behind a residue called lignin, a component of plant cell walls. That leftover lignin isn’t good for much and often gets burned or tossed into landfills. Now, researchers report transforming lignin into carbon fiber to produce a lower-cost material strong enough to build car or aircraft parts.

The researchers present their work at the 254th National Meeting & Exposition of the American Chemical Society (ACS). ACS, the world’s largest scientific society, is holding the meeting through Thursday. It features nearly 9,400 presentations on a wide range of science topics.

“Lignin is a complex aromatic molecule that is mainly burned to make steam in a biorefinery plant, a relatively inefficient process that doesn’t create a lot of value,” says Birgitte Ahring, Ph.D., the principal investigator on the project. “Finding better ways to use leftover lignin is really the driver here. We want to use biorefinery waste to create value. We want to use a low-value product to create a high-value product, which will make biorefineries sustainable.”

In addition, there are potential benefits on the carbon fiber side of the equation. Carbon fiber made with lignin would be more sustainable and less expensive than fibers currently being produced. The carbon fiber found in modern cars and aircraft are typically made from polyarylonitrile (PAN), which is a pricey, non-renewable polymer. “PAN can contribute about half of the total cost of making carbon fiber,” Jinxue Jiang, Ph.D., says. He is a postdoctoral fellow in the Ahring laboratory at Washington State University. "Our idea is to reduce the cost for making carbon fiber by using renewable materials, like biorefinery lignin." Other researchers have tried to make carbon fibers from 100 percent lignin, Jiang says, but ended up with a fiber too weak for the automotive industry. "We wanted to combine the high strength of PAN with the low cost of the lignin to produce an automobile-grade carbon fiber."

To develop a strong yet cheap carbon fiber, Ahring’s team mixed lignin with PAN in varying amounts, from 0 to 50 percent. They melded the polymers together into a single fiber using a process called melt spinning. “You elevate the temperature of the polymer blend until it melts, so it can flow,” Jiang says. “Then, you spin these polymer melts until the fiber forms.” Using a variety of methods, including nuclear magnetic resonance spectroscopy, calorimetry and electron microscopy, the researchers evaluated the fibers’ structural and mechanical characteristics. They found that they could get away with as much as 20-30 percent lignin without sacrificing strength. The lignin carbon fibers could, the researchers say, have automobile applications such as internal parts, castings and tire frames.

As a next step, the researchers will be taking their fibers to an automobile manufacturing plant to test their strength in a real-world scenario. “If we can manage to get a fiber that can be used in the automobile industry, we will be in a good position to make biorefineries more economically viable, so they can sell what they usually would discard or burn,” Ahring says. “And the products would be more sustainable and less expensive.”

Funding for the research comes from the National Science Foundation Center for Bioplastics and Biomaterials along with Ford and Hyundai Motor Companies.

For more information:
www.acs.org

Publication date: 8/24/2017

 


 

Other news in this sector:

10/10/2017 Vertical farming's best kept secret?
10/9/2017 Considerations for fine-tuning your fertilizer program
10/5/2017 US (OR): Lean group boosts value for Marion Ag Service
9/29/2017 "Ballerina is an enthusiast’s rose"
9/26/2017 CERSAA presented FERTINNOWA at VII Summer School of Floriculture
9/21/2017 Do PGRs affect overwintering survival of herbaceous perennials?
9/19/2017 Hoogendoorn whitepapers on Next Generation Growing available via webinars
9/15/2017 "Appreciation for Dutch knowledge in Kenya and Tanzania"
9/15/2017 Finding of self-medicating behavior in bees not supported in further research
9/8/2017 USA tips for growing cyclamen
9/8/2017 Cool growing poinsettias
9/6/2017 How plants turn off genes they don’t need
9/1/2017 Leaf sensors can tell farmers when crops need to be watered
8/31/2017 US (CO): Growing rudbeckias with LED
8/29/2017 MPS introduces new uniform vignette
8/29/2017 How to grow tulips in winter
8/24/2017 How to protect Phalaenopsis against Ethylene
8/22/2017 Why the color of light matters
8/16/2017 How to prevent hibiscus stem breakage
8/16/2017 Oxygenation techniques in hydroponic pelargonium

 

Leave a comment: (max. 500 characters)

  1. All comments which are not related to the article contents will be removed.
  2. All comments with non-related commercial content, will be removed.
  3. All comments with offensive language, will be removed.




  Display email address

  new code