Job offersmore »
- Head Grower, Retractable Roof Shadehouse - Wedgecarrup, Australia
- National Nursery Manager - Melbourne, Australia
- Lighting Applications Specialist (Horticulture) - Beamsville, Ontario, Canada
- Gärtner für den konventionellen Gemüsebau - Austria
- Expert vegetable farm manager/master grower seeking for his next position
- Horticulture Advisor - The Hague, the Netherlands
- Growing Manager - Victoria, Australia
- Service Engineer - Almeria, Spain
- Horticultural Consultant - Sydney, Australia
- Technical Assistant - East Malling (Kent), UK
Last commentsmore »
- India: Government gives 50% subsidy on a poly house (833)
- Will sea freight be an alternative to Latin American air freight? (7)
- "25% annual production growth Mexican phalaenopsis" (2)
- Preview FlowerTrials 2017: Novelties highlighted (1)
- India: The story of KF Bioplants (1)
- "Nursery industry shines at blossoming international floriculture trade" (1)
- "Horticulture in Iran can be an alternative to petroleum" (5)
- Netherlands 50 million stems a year at V.d. Berg Roses (1)
- Update from Dümmen Orange infected begonia cuttings (1)
- US: Congressman visits florist (1)
Top 5 - yesterday
Top 5 - last week
Top 5 - last month
Exchange ratesmore »
Different types of limestone to increase substrate pHMichigan State University Extension provided recommendations on how growers can determine greenhouse substrate pH and reviewed corrective procedures on how to increase low substrate pH in a previous article, “Testing and corrective procedures for low substrate pH.” Many growers are testing incoming substrate pH and are reporting the pH of some batches of peat mixes are inconsistently low: between 4.0 and 5.4. The recommendations on correcting substrate pH will differ significantly depending on the pH of the incoming substrate.
Growers should always check the initial substrate pH of each bale before amending any pulverized 100- or 200-mesh (particle size) calcitic or dolomitic limestone. The initial substrate pH will be the foundation and will help determine how many pH units increase are needed. Therefore, a grower with a bale of peat:perlite mix with a pH of 4.0 will need to amend the mix with more lime to raise the pH to 6.0 than if a bale had a pH of 5.0.
Photo 1. Pulverized or 100 mesh dolomitic limestone is the least reactive in adjusting substrate pH because the particles are larger, similar to sand. All photos: W. Garrett Owen, MSU Extension.
Two types of limestone are commonly available and used in adjusting the pH of greenhouse and nursery substrates: calcitic limestone and dolomitic limestone (see table). Hydrated limestone [Ca(OH)2] is another option, but it is less frequently used because it is more caustic.
Horticultural limestones are also available in two common particle size distributions, pulverized (100 mesh; 60 percent passing through a 100 mesh screen, see Photo 1) or superfine (200 mesh; 60 percent passing through a 200 mesh screen, see Photo 2). These terms are often used interchangeably in the horticulture industry to describe the particle size or mesh size distributions.
Photo 2. Superfine or 200 mesh calcitic limestone is the most reactive in adjusting substrate pH because the particle are smaller, similar to powder sugar.
In general, superfine (200 mesh; smaller particles) is more reactive in adjusting substrate pH compared to pulverized (100 mesh; larger particles) because superfine limestone has more surface area and has a greater cation exchange capacity (CEC) (Photo 3). Growers need to be aware that the pulverized limestone, which is less reactive, may slowly increase the pH and then slowly decline once it has all broken down. Similarly, superfine limestone will quickly change the pH of the substrate, but the pH could then quickly decrease over the course of a few weeks. Therefore, soilless substrate manufacturers often mix both particle sizes into their mixes, which helps to regulate the pH more consistently throughout the crop’s growing season.
Photo 3. Pulverized dolomitic limestone is the least reactive while superfine calcitic limestone is the most reactive in the substrate.
Limestone hardness refers to the soft or hard and smooth mineral structure of limestone crystals. Agricultural and horticultural limestones are considered soft crystals, reacting quickly with acid, which are more desirable in adjusting the pH of substrates formulated with peat moss, pine bark or coconut coir. Therefore, determining the rate of limestone incorporation required to adjust substrate pH depends on the components of the substrate and the type, particle size and hardness of limestone incorporated.
Part 2 of this series discusses the commonly-used limestone products for adjusting soilless substrate pH.
Source: MSU Extension
Publication date: 3/23/2017
Other news in this sector:
Leave a comment: (max. 500 characters)
- All comments which are not related to the article contents will be removed.
- All comments with non-related commercial content, will be removed.
- All comments with offensive language, will be removed.